Document IIF
Étude des performances du compresseur à double vis à gaz d’évaporation basée sur la méthode de couplage thermique fluide-structure.
Study on the performance of the boil-off gas twin-screw compressor based on the thermal-fluid-structure coupling method.
Résumé
The boil-off gas (BOG) twin-screw compressors are widely used in the transportation of liquefied natural gas. A thermal-fluid-structure (TFS) simulation model of the screw compressor is established based on the conjugated heat transfer and weak fluid-structure coupling method. The thermal deformation of the structure at a steady state is considered in the CFD simulation to improve the calculation accuracy. The accuracy of the calculation results was verified by the experiment on a high-speed oil-free twin-screw air compressor. The thermal performance and the compressor efficiencies at different operating conditions were obtained by simulations. It was found that the volumetric efficiency increased from 67 to 78 % while the isentropic efficiency increased from 64 to 75 % with increasing the suction temperature. The volumetric efficiency reduced from 76 to 71 % with increasing the discharge pressure while the isentropic efficiency reached the maximum value of 70 % when the discharge pressure was equal to the end-of-compression pressure. Besides, when the rotational speed was lower than 6000 rpm, increasing the rotational speed had a significantly positive effect on the compressor efficiencies. The volumetric efficiency increased slowly when the speed raised from 6000 to 10,000 rpm. The isentropic efficiency reached a maximum of 73 % at the speed of 8000 rpm, which decreased to 72 % at 10,000 rpm.
Documents disponibles
Format PDF
Pages : 17-31
Disponible
Prix public
20 €
Prix membre*
Gratuit
* meilleur tarif applicable selon le type d'adhésion (voir le détail des avantages des adhésions individuelles et collectives)
Détails
- Titre original : Study on the performance of the boil-off gas twin-screw compressor based on the thermal-fluid-structure coupling method.
- Identifiant de la fiche : 30032350
- Langues : Anglais
- Sujet : Technologie
- Source : International Journal of Refrigeration - Revue Internationale du Froid - vol. 163
- Date d'édition : 07/2024
- DOI : http://dx.doi.org/10.1016/j.ijrefrig.2024.04.011
Liens
Voir d'autres articles du même numéro (5)
Voir la source
Indexation
-
Thèmes :
Compresseurs;
GNL et GPL - Mots-clés : Compresseur à vis; GNL; Modélisation; Experimentation; Banc d'essai; Propriété thermodynamique; Simulation; Rotor; Rendement volumetrique
-
Development of experimental test rig for intern...
- Auteurs : KRUPA A., KOVACEVIC A., READ M.
- Date : 15/07/2022
- Langues : Anglais
- Source : 2022 Purdue Conferences. 26th International Compressor Engineering Conference at Purdue.
- Formats : PDF
Voir la fiche
-
CFD analysis of oil distribution in oil-injecte...
- Auteurs : ZHANG J. W., HSIEH S. H., HUANG C. S.
- Date : 09/07/2018
- Langues : Anglais
- Source : 2018 Purdue Conferences. 24th International Compressor Engineering Conference at Purdue.
- Formats : PDF
Voir la fiche
-
Experimental study and model optimization of th...
- Auteurs : ZHANG H., ZHANG Z., TONG L., YANG J., LI Y., WANG L., GUO X., TIAN R., HE M., GAO C.
- Date : 05/2024
- Langues : Anglais
- Source : International Journal of Refrigeration - Revue Internationale du Froid - vol. 161
- Formats : PDF
Voir la fiche
-
A proposal of graphing methods for improved com...
- Auteurs : SJOHOLM L., MA Y. C., WYNN B.
- Date : 15/07/2022
- Langues : Anglais
- Source : 2022 Purdue Conferences. 26th International Compressor Engineering Conference at Purdue.
- Formats : PDF
Voir la fiche
-
Refreshed internal working characteristics of t...
- Auteurs : WU W., ZHANG Z., PENG C., LI X., YANG Y., LEI W.
- Date : 11/2022
- Langues : Anglais
- Source : International Journal of Refrigeration - Revue Internationale du Froid - vol. 143
- Formats : PDF
Voir la fiche